Are you concerned about storm water run-off? If you're in charge of an industrial facility, a parking lot, or another type of vehicle storage area, you have to be concerned about oil and BIC licensed grease removal NYC in storm water. Read on for an easy solution to your problem.
An interceptor is simply a box-shaped device that is installed between the kitchen drain and the main sewage system. It is designed to filter and trap the heavier oil and oil from the water that flows through it and will hold it there until the opportunity for cleaning oil traps presents itself.
These vehicles have one thing in common... They often leak, especially oil and other fluids. And whatever fluids they leak, if they're not caught and cleaned up immediately, they'll end up sitting on the surface of the parking lot, waiting for the next rainfall. And as soon as that rainfall comes, they're swept up in storm water run-off, and off into the ground water they go. Unless...
All you need to do is sprinkle some of the powder on the oil spot, and let it soak in for about 15 minutes. Then, you can easily scrape or vacuum up the powder, along with a lot of the oil. (You may need to do this a couple of times if there was a lot of oils until no more seems to be soaked up by the powder.)
Remove the oil remaining on the carpet with dry cleaning solvent. As we all know oil and water, don't mix, and therefore you must use a solvent, such as dry cleaning fluid, to remove the rest of the oil from the carpet. To do this apply a small amount of dry cleaning solvent to a white cloth and gently blot at the oil spot, allowing the oil to transfer from the carpet onto the cloth. Continue blotting until the spot is removed. You may need to periodically blot with a new area of the white cloth to keep oil from re-transferring from the cloth back onto the carpet during this blotting process.
Fortunately, it also has a fairly high capacity -- depending on size, it can hold between nearly a gallon and about 1.3 gallons of oil before it is saturated. It can also hold sediment -- up to 40 lbs. So it will last for a while, but not forever, so you do need to keep extras at hand, in case your first one fills up.
Continue dipping in the solution until the oil has been completely removed. This will probably remove some of the dirt, but some residue will remain. Wipe the surface with a fresh, lukewarm water-rinsed rag to remove the remaining residue. Do a second pass of cleaning by wiping it again with a clean, dry rag. Repeat for every greasy part of the kitchen.
Keep in mind that grime from kitchen cabinets are different because the oil from some of the foods evaporates into the air, seeping into the cabinets, the ceiling, even the refrigerator. The vinegar might be optional, but it is highly recommended that you include it in the solution, since the acidic nature of the vinegar will help. There will be a hint of the sourness, but the second and third wipes will take care of the unnecessary odor.
An interceptor is simply a box-shaped device that is installed between the kitchen drain and the main sewage system. It is designed to filter and trap the heavier oil and oil from the water that flows through it and will hold it there until the opportunity for cleaning oil traps presents itself.
These vehicles have one thing in common... They often leak, especially oil and other fluids. And whatever fluids they leak, if they're not caught and cleaned up immediately, they'll end up sitting on the surface of the parking lot, waiting for the next rainfall. And as soon as that rainfall comes, they're swept up in storm water run-off, and off into the ground water they go. Unless...
All you need to do is sprinkle some of the powder on the oil spot, and let it soak in for about 15 minutes. Then, you can easily scrape or vacuum up the powder, along with a lot of the oil. (You may need to do this a couple of times if there was a lot of oils until no more seems to be soaked up by the powder.)
Remove the oil remaining on the carpet with dry cleaning solvent. As we all know oil and water, don't mix, and therefore you must use a solvent, such as dry cleaning fluid, to remove the rest of the oil from the carpet. To do this apply a small amount of dry cleaning solvent to a white cloth and gently blot at the oil spot, allowing the oil to transfer from the carpet onto the cloth. Continue blotting until the spot is removed. You may need to periodically blot with a new area of the white cloth to keep oil from re-transferring from the cloth back onto the carpet during this blotting process.
Fortunately, it also has a fairly high capacity -- depending on size, it can hold between nearly a gallon and about 1.3 gallons of oil before it is saturated. It can also hold sediment -- up to 40 lbs. So it will last for a while, but not forever, so you do need to keep extras at hand, in case your first one fills up.
Continue dipping in the solution until the oil has been completely removed. This will probably remove some of the dirt, but some residue will remain. Wipe the surface with a fresh, lukewarm water-rinsed rag to remove the remaining residue. Do a second pass of cleaning by wiping it again with a clean, dry rag. Repeat for every greasy part of the kitchen.
Keep in mind that grime from kitchen cabinets are different because the oil from some of the foods evaporates into the air, seeping into the cabinets, the ceiling, even the refrigerator. The vinegar might be optional, but it is highly recommended that you include it in the solution, since the acidic nature of the vinegar will help. There will be a hint of the sourness, but the second and third wipes will take care of the unnecessary odor.
About the Author:
You can get great tips on how to select a grease disposal company and more information about a BIC licensed grease removal NYC company at http://www.mesoapcompany.com/grease-removal-faq.html now.
No comments:
Post a Comment