At times, a person may be on the road for so long that they do not have time to settle and secure a place for their property. This is especially musicians and even show who decide to take their talent on the road. Since it is impossible to travel with the whole house, you will need to own custom road cases. They protect your property and below is how to make them.
You need to set up a place where you will be spending most of your time building the case. You should make sure that you have all the equipment you need in order to move the process along faster. Make sure that you have a cut list to avoid wasting any material. You are to build the case according to the size of the item you are building the case for.
After gathering everything you need, you need to get to work. You should start off by cutting the aluminum. Aluminum is not only one of the strongest elements of this case but it is also decorative. That shiny new look gives some elegance to it. It is recommended that It is best to use a cold saw to avoid any kind of damage to the aluminum.
The notches and pockets are made out of wood. In order to avoid a messy job, it is important to use a jigsaw in cutting the wood. You cannot be able to draw or see the markings on the black ABS. It is, therefore, best to put the markings on the unfinished side. You should trim down the u-channels to match with the notches.
You need to attach the ball corners. There is no way a case would work if it did not have any corners. The corners allow the case to hold everything inside without falling apart. They are not held together by nails or glues as one may presume. They are actually held together by rivets. To put the rivets in place, you may use the handgun or the pneumatic rivet which is recommended.
After putting in the ball corners, the straight ones should be next. These allow the road to stand upright. You will need to drill some holes and put in some screw in order for the pieces of the road to come together. You can start by putting in a screw in every end then proceed for round two as a way of reinforcement.
For the bottom part, you may choose to use a rubber or wheel, whichever you are most comfortable with. As you assemble the road, make sure it is in a closed position. This makes the work easier and allows you the preview of how the road will look after the work is done. Align the corners to ensure that the hinges stay in line.
Finally, you will need to have foam in your case. That foam acts as a shock absorber no wonder it looks so comfortable. While putting it in place, start from the bottom upwards. The foam on the walls, however, should be shorter than the walls to avoid hindering the closing of the case.
You need to set up a place where you will be spending most of your time building the case. You should make sure that you have all the equipment you need in order to move the process along faster. Make sure that you have a cut list to avoid wasting any material. You are to build the case according to the size of the item you are building the case for.
After gathering everything you need, you need to get to work. You should start off by cutting the aluminum. Aluminum is not only one of the strongest elements of this case but it is also decorative. That shiny new look gives some elegance to it. It is recommended that It is best to use a cold saw to avoid any kind of damage to the aluminum.
The notches and pockets are made out of wood. In order to avoid a messy job, it is important to use a jigsaw in cutting the wood. You cannot be able to draw or see the markings on the black ABS. It is, therefore, best to put the markings on the unfinished side. You should trim down the u-channels to match with the notches.
You need to attach the ball corners. There is no way a case would work if it did not have any corners. The corners allow the case to hold everything inside without falling apart. They are not held together by nails or glues as one may presume. They are actually held together by rivets. To put the rivets in place, you may use the handgun or the pneumatic rivet which is recommended.
After putting in the ball corners, the straight ones should be next. These allow the road to stand upright. You will need to drill some holes and put in some screw in order for the pieces of the road to come together. You can start by putting in a screw in every end then proceed for round two as a way of reinforcement.
For the bottom part, you may choose to use a rubber or wheel, whichever you are most comfortable with. As you assemble the road, make sure it is in a closed position. This makes the work easier and allows you the preview of how the road will look after the work is done. Align the corners to ensure that the hinges stay in line.
Finally, you will need to have foam in your case. That foam acts as a shock absorber no wonder it looks so comfortable. While putting it in place, start from the bottom upwards. The foam on the walls, however, should be shorter than the walls to avoid hindering the closing of the case.
About the Author:
You can find a detailed overview of the benefits you get when you order custom road cases at http://www.encorecases.com/products right now.
No comments:
Post a Comment