You do not need to worry so much. Because you will always find a way how to do it. You can always find a solution to a problem. Just follow the step by step process. To make the project successful.Get ready all the stuff that is needed. And see the outcomes after. And be amazed of the results.
Gather them all together. And you have to list down the instructions as your guide. Especially for beginners. You need to have a guide in doing the reflow soldering oven. All you should do is just to follow the steps that will makes your project a success. Some people will try to invent their own without knowing the risk. Make sure to have an oven toaster to do it. That is the essential thing to use.
Get ready with the thermometer and a timer. Do not rely on the one that is found in the oven. You are required to get one. No need to get the best quality. Just the one you can use and will give accurate results. You can also use them in other projects. What matters most is they work great.
Time to make the motherboard. It will not take time for you. Especially you have a draft of it already. And how do you want them to be. This will be your plan. Better check everything and see if there is lacking. So there is no regrets later. If there is something that you missed, you would have to start from scratch again.
After you are done making them, you may now add some flux so you could modify later. This is very important that you put them on top of the board to avoid the balls from flowing to any location. So the reflow will become successful.
Align the components. Open the door, then align them inside the flat surface. Use a silk screen to do the alignment and can be use for outlining. This is give assurance that everything put there. Most will not be accurate especially if they will melt after.
Start them cooking. Ensure that they perfectly fit inside. And the surface must be elevated. You can now turn on them on to see the outcome of experiment. The maximum time you would cook them are 20 minutes. Do not go beyond the time limit so they will not damage. Make sure you close the door once the cooking is ongoing. You are not allowed to open them if the allocated time is not yet over.
Let them cool. If it is done, turn them off right away. The best and only way to cool them down is to open the door. Never touch anything nor move them around. It will not take long and check if the temperature drops to 50 degrees Celsius. Then you are assured that they are cold already. That is you way to see if they are okay already. If you think they are still hot enough, then leave them and come back when it is okay.
And come back again to check if the experiment is a success. And see if everything are connected. Especially the balls since they are the most important. If all are connected, it only means that you did a great job.
Gather them all together. And you have to list down the instructions as your guide. Especially for beginners. You need to have a guide in doing the reflow soldering oven. All you should do is just to follow the steps that will makes your project a success. Some people will try to invent their own without knowing the risk. Make sure to have an oven toaster to do it. That is the essential thing to use.
Get ready with the thermometer and a timer. Do not rely on the one that is found in the oven. You are required to get one. No need to get the best quality. Just the one you can use and will give accurate results. You can also use them in other projects. What matters most is they work great.
Time to make the motherboard. It will not take time for you. Especially you have a draft of it already. And how do you want them to be. This will be your plan. Better check everything and see if there is lacking. So there is no regrets later. If there is something that you missed, you would have to start from scratch again.
After you are done making them, you may now add some flux so you could modify later. This is very important that you put them on top of the board to avoid the balls from flowing to any location. So the reflow will become successful.
Align the components. Open the door, then align them inside the flat surface. Use a silk screen to do the alignment and can be use for outlining. This is give assurance that everything put there. Most will not be accurate especially if they will melt after.
Start them cooking. Ensure that they perfectly fit inside. And the surface must be elevated. You can now turn on them on to see the outcome of experiment. The maximum time you would cook them are 20 minutes. Do not go beyond the time limit so they will not damage. Make sure you close the door once the cooking is ongoing. You are not allowed to open them if the allocated time is not yet over.
Let them cool. If it is done, turn them off right away. The best and only way to cool them down is to open the door. Never touch anything nor move them around. It will not take long and check if the temperature drops to 50 degrees Celsius. Then you are assured that they are cold already. That is you way to see if they are okay already. If you think they are still hot enough, then leave them and come back when it is okay.
And come back again to check if the experiment is a success. And see if everything are connected. Especially the balls since they are the most important. If all are connected, it only means that you did a great job.
About the Author:
When you are searching for the facts about a reflow soldering oven, go to our website today. More details can be seen at http://www.sikama.com now.
No comments:
Post a Comment